[SEARs]

yeah but can he connect to the abs system?

ME3.1 is the engine ecu, not airbag

 

[SEARs]

as you look at the cars conector the layout is:

top LHS
1--2--3--4--5--6--7--8
9-10-11-12-13-14-15-16
Bottom LHS

keep this in mind when looking at the connector.

I've used my 2 interfaces in a Doblo-JTD, same diag port as in your 147 with any issues.

Kwp71 only goes as far as Com 8..... make sure to select Com POrt 1st

Did you OPEN PORT?

Did you select the correct options [ KWP81 & 0x00 ]

Did you Start Comms

if oyu want i cna call over to sort it for you, if oyu pay the airplane ticket

 

[SEARs]

Draco13, maybe your car falls into the same category:

The newer ABS ECUs (in e.g. 147) already use kwp2000, so
UniDiagKWP2000 can be used.

Here are some faultcodes for the ABS:

0x5200 FRH speed sensor, wiring error
0x5201 Front RH wheel speed sensor
0x5205 FLH speed sensor, wiring error
0x5206 Front LH wheel speed sensor
0x5210 RRH speed sensor, wiring error
0x5211 Rear RH wheel speed sensor
0x5215 RLH speed sensor, wiring error
0x5216 Rear LH wheel speed sensor

 

[SEARs]

Draco13, hope get it sorted soon.

 

[draco13]

Draco13, hope get it sorted soon.

I think I could go to Ireland so you explain to me, I think it is a great excuse to go over there...

I think I may have a problem with the interface, I took pin 10 away and solder it to pin 1 but still cant connect.
I´m using the blue interface because I think the black one that came with my ELM327 doesn´t work with alfas
Do you think I should by another interface?

 

[draco13]

as you look at the cars conector the layout is:

top LHS
1--2--3--4--5--6--7--8
9-10-11-12-13-14-15-16
Bottom LHS

keep this in mind when looking at the connector.

I've used my 2 interfaces in a Doblo-JTD, same diag port as in your 147 with any issues.

Kwp71 only goes as far as Com 8..... make sure to select Com POrt 1st

Did you OPEN PORT?

Did you select the correct options [ KWP81 & 0x00 ]

Did you Start Comms

if oyu want i cna call over to sort it for you, if oyu pay the airplane ticket

Yes, I did exactly this but can´t connect. Thats why I think my interface is wrong or something

 

[SEARs]

did you connect a wire form 7 to 1 also?

if not you need to do this as the default communication/wiring only goes to 7

 

[draco13]

Draco13, maybe your car falls into the same category:

You are right on this, I checked the car and it uses KWP2000. Is that good or bad? I´m lost, sorry.

 

[SEARs]

who was it htat connected using KWp2000?

he posted a thread with 5216 error

 

[SEARs]

http://www.alfaowner.com/Forum/alfa-147-156-and-gt/155588-still-not-fixed-abs-problem.html

he use dthe 'Bosch' def file ???

Pin 1 seems to be still required

maybe YOU Draco13 can start a threa dhow to use KWP2000 with abs

 

[SEARs]

you need to download the latest KWP2000 0-4-0-3

in that is the 'bosch' def file

Test_BoschABS57ASRTC

 

[SEARs]

now!!!! hop to it!!!!

 

[draco13]

Jaja, thanks a lot! I´ll try that now and see what happens!

 

[draco13]

I solder pin 1 to 7. Is there any way I can check if the interface is working or in good condition? With a multimeter or something?

 

[SEARs]

if the interface talks to the main ecu, that proves it works .... can it?

after that then check resistance from 7 to 1 with a meter.

do you have eLearn?

 

[draco13]

no, it doesn´t talk to the main ecu and I don´t even know what elearn is. I´ll try checking resistance

 

[draco13]

if the interface talks to the main ecu, that proves it works .... can it?

after that then check resistance from 7 to 1 with a meter.

do you have eLearn?

Hello! Im closer!!!
These are the news: I downloaded the new unidiag. I get 2 kind of errors now. If I try to load the Test_BoshASR etc definition, it gives me an erro on Unidiag --> ( " is not a valid integr value)
If I try to load another definition, it works but when I try to Start+id it gives me another error on unidiag -->"Exception bla bla in module UnidiagWp2000.exe at 00032033a blablabla Out of range :-[ and OBD ERROR LIGHT on dashboard. I feel I´m closer now.... Please helppp

 

[SEARs]

new def file uploaded tonight:

http://autos.groups.yahoo.com/group/UniDiag/files/DefinitionFiles_AlfaFiatLancia/

bottom of page

apparently if you just use Unidiag2000 WITHOUT a *.def file it'll read the errors

Yahoo! Groups

 

[SEARs]

FAO Yarslberg

 

[SEARs]

Hello! Im closer!!!
These are the news: I downloaded the new unidiag. I get 2 kind of errors now. If I try to load the Test_BoshASR etc definition, it gives me an erro on Unidiag --> ( " is not a valid integr value)
If I try to load another definition, it works but when I try to Start+id it gives me another error on unidiag -->"Exception bla bla in module UnidiagWp2000.exe at 00032033a blablabla Out of range :-[ and OBD ERROR LIGHT on dashboard. I feel I´m closer now.... Please helppp

Draco: did you try downlaoding this file:

Test2_BoschABS57ASRTC.def

i used it today on a 2.0L JTS & it works PERFECT:thumbs: