Alfa Romeo Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 28 Results
  1. Alfa Giulietta
    Quick question: Can anyone confirm the correct tools required for the undertray removal please? I'm hoping to do an oil and filter change at the weekend, and to save me scrabbling around under the car tonight (when I should be ferrying the kids round to their Thursday night swimming / scouts /...
  2. Alfa 159, Brera & Spider
    Just looking at my upper wishbone bolts from the side I would say that they look like about an E18 size torx. Can anyone confirm this? I'm replacing the NS upper wishbone on Friday and just want to make sure that the torx socket I need isn't one of the ones that have gone AWOL over the years...
  3. Alfa 147, 156 & GT
    Need to remove the rear bumper of the Alfa. Does anyone know what size of Torx screwdrivers I'll need? Cheers, PP.
  4. Alfa Giulietta
    Another question... Can anyone remember off of the top of their head the size of the Torx bit required to remove the large bolts which retain the bumper in the bonnet shut area? I am going to buy a tool as I know I haven't got one. Many Thanks. :)
  5. Alfa 147, 156 & GT
    Hi I'm fixing my arm rest and I'm missing 3 of the 4 torx screws. Think they are 12mm lengh/ 6mm head diameter. They are black and fit on the hinge. I've tried b&q screwfix halfords but no one has them. Has anyone got any or know where I can get them please? See attached pics Regards
  6. Alfa 147, 156 & GT
    Hi I'm fixing my arm rest and I'm missing 3 of the 4 torx screws. They are black and fit on the hinge. I've tried b&q screwfix halfords but no one has them. Has anyone got any or know where I can get them please? Regards
  7. Alfa 159, Brera & Spider
    Can anyone tell me the size of the torx bolt for removing the "frame" for the rear brake calipers on a 159 SW? (Dont know the correct englisg term for the "frame". But it is the part that the caliper is bolted on to.)
  8. Alfa 159, Brera & Spider
    Does anyone have a reasonable list of which Torx socket and bit sizes are needed to work on a 159? And if they are Torx, Torx-Plus or Ribe? For instance I am thinking about what sized Torx "E" sockets I need to remove the brake calipers, drop off the front subframe, undo wishbone and lower-arm...
  9. Alfa 147, 156 & GT
    Can somebody tell me what size the Torx head is that I need to remove the door on the back of my 156 Sportwagon? I don't have any of these and don't want to buy a tool that doesn't fit!
  10. Alfa 159, Brera & Spider
    As above really. Currently attempting to change my rear discs/pads after successfully changing the fronts however I've come unstuck in removing the rear caliper to access the discs. I know that the front size is E18, but unsure on the rear! :confused: Thanks in advance!
  11. Alfa 147, 156 & GT
    Does anyone know what size the torx screw bit is for the engine mount of 147 1.9 8v?
  12. Alfa 147, 156 & GT
    Hi guys, I'm 99% sure my top-mount is shot. Have replaced the wishbones and droplinks and tested the roll bar and it's fine. The noise is knocking/rattling on the drivers side over rough ground and on acceleration/breaking and is often accompanied by a creaking/groaning. I've taken a look at...
  13. Alfa 159, Brera & Spider
    I have got to do front discs and pads on my 159 soon, does anyone know what size torx socket I need?
  14. Alfa GTA
    What size torx screwdriver do I need to remove the undertray? I take it I need to remove the screws that are holding it to the front bumper? And then there seemed to be a few bolts to remove at the sides, is that correct? Getting too dark to see properly and i'd like to order a torx driver to...
  15. Alfa 147, 156 & GT
    I need to buy a torx bit so I can adjust the latch on the B pillar, does anyone know the size by any chance?
  16. Alfa 33, Sud & Sprint
    could some one please tell me the size of the torx key i need to undo the head bolts on a 16v 33. i know i read it here only last week but i have to go out now and dont have the time to look. cheers for your help harry
  17. Engines (TS, JTS, JTD & V6)
    Hi, planning to change crankshaft pulley on my 166 JTDm because it wobbles. It is fastened with six bolts that seems to have a strange bit type. Is it a torx or a torx-plus or something else? And what size of the bit is needed? /Magnus
  18. Alfa 147, 156 & GT
    Having had an advisory on my last MOT for a corroded n/s wing, I decided on getting a replacement. Managed to get hold of one, in the right colour, for the right price a couple of weeks ago (and a couple of headlights into the bargain). Did the GTA mod on the headlights, and the new sealant is...
  19. Alfa 147, 156 & GT
    Hi, Anyone know where to get replacement torx screws for the bottom engine cover? It's the ones with big flat head - there are 3 along the front and one either side where the cover attaches behind the wheelarches. Somehow managed to lose a couple - scared the whole thing is gonna fly off now...
  20. Alfa 147, 156 & GT
    hi all,need to get torx screwdriver to remove security screws on maf,what to get and where would be a great help !
1-20 of 28 Results
Top