Alfa Romeo Forum banner

torque

  1. Flywheel bolt torque settings

    Alfa MiTo
    Hi I am going to be changing my clutch and dmf tomorrow only thing im struggling to find anywhere is the torque settings for the flywheel bolts hopefully someone can help me out thank you its a 2012 1.4 multiair 135bhp
  2. Torque App

    Alfa GTA
    Hi Is anyone using the Torque Pro App on a 147 GTA ? I bought a quality Bluetooth interface and the App connects successfuly to it, but wont connect to the ECU, error message "unable to connect to ECU", indicating car is non OBD2 compliant. Any ideas? I also use MES with a cable connection...
  3. Remapping extra Bhp and Torque

    Alfa Giulia
    Morning all, toying with the idea of adding that extra bit of grunt, please see below what I’ve had quoted. Anyone else done something similar are there pros cons well let’s be honest what are the cons!!!! Celtic TuningCeltic TuningCeltic TuningTHE PERFORMANCE Celtic TuningCeltic Tuning The...
  4. Torque vectoring

    Alfa Giulia
    What cars have the torque vectoring function? is it just the QF? Reason I ask is that I had a very quick right hand pull away and I noticed the back end slided and then seemed to magically straighten out. The wife told me to stop driving it like I stole is so it was a pretty good event in my...
  5. Torque figures for brake change, anyone?

    Alfa Giulietta
    With a new car I normally buy a new Haynes manual, mainly for the torque figures. As there isn't such a thing for the Giulietta, and I've just ordered some discs and pads (front and rear), does anyone have any torque figures for slider pins, calliper mount, etc? I have a bit of an over...
  6. 164 torque setting

    Alfa 164 & 166
    anyone know the correct spark plug torque for a 3.0 24v 164?
  7. Torque settings?

    Alfa 147, 156 & GT
    Hi folks, anyone know where I can get a complete list of torque settings for 147, mainly suspension related rather than engine block?
  8. Source for torque settings?

    Alfa GTV & 916 Spider
    I dropped off the heads of my V6 for skimming today, following a head gasket failure on the rear bank. I'm hoping to get them back and to start the rebuild this weekend, which means I will need torque settings for various nuts and bolts. I can't see these in the technical manual - "repair...
  9. Steering wheel retaining nut torque

    Alfa 159, Brera & 946 Spider
    Hi All does anyone have the torque figure for the 24mm steering wheel retaining nut? Can't get my elearn disc to load and the downloadable version is a mare to get to work. Thanks
  10. Alfa 156 JTS Cambelt Idler torque

    Alfa 147, 156 & GT
    Apologies if this is a duplicate but I can't seem to find the answer in the other cambelt change posts. I'm changing the variator, cambelt, water pump, balancer belt plus associated idlers etc on a 2005 156 JTS I've just bought and I can't seem to find what the torque setting is for the cambelt...
  11. Crank pulley bolt torque?

    Alfa 159, Brera & 946 Spider
    I'm hoping to fit a new ribbed belt crank pulley (TVD) to my 2.0JTDm this weekend...I say hopefully as I was supposed to have the part last Tuesday via a 24 hour courier ....several stroppy emails later and I still don't have it! Anyway....assuming it comes does anybody know the correct torque...
  12. Brera rear trailing arm bolts torque?

    Alfa 159, Brera & 946 Spider
    Hi guys I have just refurbished the trailing arms for my brera I am going re fit them now, so could someone tell me what torque the bolts need to be tightened to please? I haven’t got an Elearn CD so could someone help me out please Many thanks in advance
  13. Front Brake Caliper Bolts Torque

    Alfa GTV & 916 Spider
    Just wondering if anyone can confirm the torque settings for the caliper carrier bolts (7mm hex) and caliper bolts (19mm socket) on the front calipers? This thread mentions the front caliper bolts are 22-32Nm. I assume this is the 7mm hex bolts as it sounds too low for the ones with the 19mm...
  14. Brera 3.2 inlet manifold torque setting?

    Alfa 159, Brera & 946 Spider
    Hi, I know I have seen this somewhere on the forum but cannot seem to find it! I have just changed the plugs on a Brera 3.2 and cannot seem to find in the inlet manifold torque setting. Can someone advise please? Thanks Nick
  15. Torque settings for engine mount bolts?

    Alfa Giulietta
    I'm going to replace the engine mount on my 2015 1.4 MA TCT - drivers side - the one under the coolant tank. Has anyone got the torque figures for the bolts? TIA!
  16. Torque Pro Android Auto

    Alfa Giulia
    I recently came across this - https://forum.xda-developers.com/general/paid-software/app-obd2-plugin-android-auto-torque-t3657805 - I've had Torque Pro for a while but always found it a bit clunky, this is pretty straightforward once you've done initial setup and chosen gauges. Is it worth...
  17. Wheel Bearing Bolt Torque

    Alfa 159, Brera & 946 Spider
    Hi All Can someone run their Elearn disc and find the torque figures for the 4 torx bolts that secure the front wheel bearing? Also the torque procedure for the 36mm Axle Nut? Sorry my disc drive has broken and no access to the info -will be changing the bearings in the morning. Thanks Paul
  18. *Advice Needed * Alfa Rocker cover Torque settings

    Alfa 147, 156 & GT
    Need to replace the rocker cover as it is cracked on my 2007 GT 2.0JTS could someone tell me the torque setting and tightening sequence? Cant find it anywhere
  19. Rear suspension torque specs

    Alfa 147, 156 & GT
    Hi all, Really struggling to find any info on the rear torque settings for my other falfs 2007 147. The two bolts I need specs for are the lower mounting bolts that go through the rear shock absorbers (19mm nuts on these ones) Anyone know these? Thank you
  20. Valve cover torque and oil leak

    Alfa 159, Brera & 946 Spider
    Hi guys. As you may know, I've just finished the initial part of project mending The Alfa. But I have a medium size oil leak. It's leaking from the rocker cover so I probably screwed something up when I replaced the gasket. There's also a leak on the timing belt side of the engine that I...
Top