stud

Hi does anyone know the size of the 3 studs that mount the HP pump onto the block? M8? X ? Sorry just wanting to buy a spare in preparation for replacing my inlet manifold. Thanks Paul

My wheel spacer kit has sat on the shelf for some considerable time because the supplied studs for the stud conversion do not have a "shoulder" and so my engineer won't fit them. Does anyone know a workshop that handles this modification? Most TS cup cars are running now with this conversion.

Hi all Got the early inlet manifold, woodruff key, gasket today to replace the current one with the swirl flaps. I'm going to use the stud extractors method instead of cutting the casing . and have a couple of questions. 1) This is the size of extractor...

Does anyone know the size of the turbo to manofold studs, m8 or m10? Thanks

Hi Guys, I need some help. I experienced a metallic grinding noise whilst running my 159 2.4 JTDm and investigation revealed that the tensioner pulley had failed sheering off the sliding fixing stud. Any idea's where I can find a replacement stud? I have bought a complete timing belt kit...

What type of sealant is best to use on Exhaust studs that are weeping oil? Is silicone up to the job or should i use exhaust sealant paste?

On a V6 trying to remove the front flexi exhaust pipe, I've snapped one of the studs between manifold and exhaust when trying to remove nut. Whats the best way of going about this without taking the manifold off, drill out remaining stud and replace with a bolt?

I did buy a kit, but what I thought was a 10 MM press stud isn't. any fixes or places to go? The "female" part of the stud is still there

I'm looking for a set of second hand wheels and was wondering what other makes of cars share the same wheel fitting. I have been told old ford wheels mat match. looking for some minilite style wheels. Thanks

hi folks, there are two studs on the exhaust manifold that hold on the heat shield, one of mine has sheared off and the heat shield vibrates when driving. before I get going on trying to remove the stud with a drill and an easy out, I'm wondering if it's ok to drive it with out the heat shield...

Anyone had any experience with Bola wheels? I get that they are knock off's of the real deal, but its so bloody hard to find wheels with our stud pattern, especially in Australia. Are the worth the dosh...

Managed to misplace one while doing the latest job. Despite keeping all the bits in a tray, it doesn't help if one treads on the side of the tray and all those carefully kept nuts, bolts and other odds and sods go flying all over the drive. Found everything bar one of the studs. Yes, I know...

my lusso 7 hole alloys are looking very tired... thinking of replacing them, does anyone know if alfas are an odd 5 stud spacing or if they are the same as other brands? as i have seen some nice multispoke similar to the 159 wheels but unsure of the stud spacings... thanks in advance... :thumbs:

I have snapped the studs that hold the exhaust centre section to the downpipe. Does anyone know if the studs should knock out, or screw out? can't see on mine as they are rusted up. May have to drill them out but would rather not. Its the ones that join the down pipe to the centre section, sort...

Does anyone know what sizes i need to go about this to fit my Facelift 147 I.e "M12x1.5, 60mm length, 17mm nuts"

Hi all i'm giving this area of the site a heads up on a clearout i'm having of some nice 4 stud alloys that will all be up for grabs shortly in the classifieds and the usual online sites. you can see detailed pictures of all sets here For Sale pictures by shrewiside - Photobucket but these...

Hi, Does anyone happen to know the thread size of 156 wheel studs? (55 reg) I know they're M12, but need to know the pitch. Reason is that I've got a cross-threaded stud and need to obtain a tap to try and fix it. Also, what type of tap should I get, and is it do-able anyhow? :D Finally...

I replaced the drivers side wishbone about a week ago, which involved loosening the three nuts at the top of the strut. So just this evening I went to check the tightness of these three nuts. I went to tighten one a little further as I thought it was a tad loose. SNAP!! The f**king bolt/stud...

Hey I'm hoping someone will be able to help me out here. I have a set of 17" 5 stud CRS Replica Alloys on my 156.. my 2 front wheels are buckled :( My tyres are good so I was hoping to just get a set of wheels without spending much money as I have recently spent a fair bit of money on my car...

I need a little help here. Could someone please tell me if the 164: 2.0 V6 turbo, 3.0 V6, 3.0 24v, 3.0 24v, 3.0 24v QV, and 2.5 TD, have 4 or 5 stud wheel fixings. Thanks very much. Peter