Alfa Romeo Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 74 Results
  1. Alfa GTV & 916 Spider
    The roof of my Spider is leaving a mark on the clamshell, tried fitting a rubber seal to it that was worse. I would like to know how to adjust the screw down screws that hold the rear of the roof to the clamshell, my worries are that if I loosen it of then it may let water in ?? Is there a...
  2. Alfa 159, Brera & Spider
    Just been reminded I have 4 fusebox cover screws for sale (one tentatively reserved) - the ones that always chew up on the interior fusebox cover. Now admittedly they are a bit steep, I had to buy a minimum of 5 at £5.86ea - just looking to cover purchase price, postage will be free within the...
  3. The Classic Alfa Romeos
    I know it's been covered a lot of times but I'm re hashing the old question about idle mixtures sorry to bring it up again but just interested in how many turns from closed are your screws at, I've just finished redoing the carburettor mounts on my 2 litre gtv and going through the adjustment of...
  4. Alfa 147, 156 & GT
    My JTS has rather corroded screws for holding the top to the housing. Are these double helix screws available or has anyone come up with a better solution? I don't want the black generic screws BTW as they corrode faster than originals.
  5. Alfa GTV & 916 Spider
    I am planning some work on my phase 1 Twinspark but I am stuck figuring out which bolts to use/order. In Eper just get a part number that is hard to find or has been replaced etc. etc. What i am looking for, and have seen for other types of alfa's, is a fasteners list which shows the specs of...
  6. Alfa 159, Brera & Spider
    Evening all, I am picking up a new to me 159 on Saturday morning and have some preventive jobs to do... Intending to do the timing belt, tensioner, waterpump, oil + filter and gearbox oil change. The vehicle is a 2009 Lusso so am i correct in assuming this will have the plastic manifold...
  7. Alfa 147, 156 & GT
    Need to remove the rear bumper of the Alfa. Does anyone know what size of Torx screwdrivers I'll need? Cheers, PP.
  8. Alfa GTV & 916 Spider
    Morning all. Anyone got any of the above spare they want to sell me? I need 2 if possible? Boot carpet hanging down and driving me mad...[emoji106]
  9. Alfa GTA
    There's three of them and they have a bolt head but they're more of a screw than a bolt. Anyway, the head on one of mine is all rusty and chewed up so I get my local dealer to order what appears to be the correct part number (7784599) but when it arrived it was a bolt and different to the part...
  10. Alfa GTA
    Hi all. Does anybody know what scews are used to secure the scuttle panel to the car. Mine only has one screw on the passenger side and it doesnt look like the proper one either. Id like to get it secured properly so that it sits nicer than it does at the moment.
  11. Alfa GTV & 916 Spider
    Hi all, as above my front fusebox cover is currently flapping around my ankles as it is held of by tie tags. Not ideal. Does anyone know of and where all the screws are still available? Thanks. Ash
  12. Alfa GTV & 916 Spider
    Hello, I notice that the two big black plastic mouldings on either side of the engine have the screws missing. They just lift off. Any ideas where I can get hold of the correct ones. Don't have a dealer near me though. Thanks.
  13. Alfa 159, Brera & Spider
    I ordered the genuine metal footrest and pedals for my 159, but it seems the screws are different on this version compared to my old one. This is the RHD one, but even so, as you can see in the pic it doesn't look like a straight swap is possible. Did anyone else have this issue or did I just...
  14. Alfa GTV & 916 Spider
    Anyone got some of those little Ivory coloured plastic boot carpet retainers the screw in (by hand) ... I've got about half a dozen missing on me GTV ..? Chiz in advance MC
  15. Alfa GTV & 916 Spider
    Hi there, I had to replace a headlight bulb on my GTV a couple of days ago on the passenger side and noticed that the screws into the plastic guard, that covers the back of the headlight and the washer bottle, are really corroded! Any idea where I can get new screws and washers from and what...
  16. Alfa 147, 156 & GT
    Hi I'm fixing my arm rest and I'm missing 3 of the 4 torx screws. Think they are 12mm lengh/ 6mm head diameter. They are black and fit on the hinge. I've tried b&q screwfix halfords but no one has them. Has anyone got any or know where I can get them please? See attached pics Regards
  17. Alfa 147, 156 & GT
    Hi I'm fixing my arm rest and I'm missing 3 of the 4 torx screws. They are black and fit on the hinge. I've tried b&q screwfix halfords but no one has them. Has anyone got any or know where I can get them please? Regards
  18. Alfa GTV & 916 Spider
    Hey, my hazard light has 0 screws in them so i have no idea what type i need, i see that the back of the center console has 2 different types (4 total) (Phase 1 GTV) opposite each other used for the hazard light switch. unfortunately i cannot get behind the center console too easy because of my...
  19. Alfa GTV & 916 Spider
    I've just noticed I'm two screws missing from either side of the cowling under the windscreen. Is anyone braking a GTV that could let me have a pair? 2 pics below, 1 is of the missing screw, and the other is another screw on the cowling I assume there the same type of screw?
  20. Alfa GTV & 916 Spider
    Hi, i wanted to know what kind of screws are used to hold on to the airbag (Ph1). I have tried everything but i cant make it budge. Torx T30 i believe is what it is but it does not work. i have 3 steering wheels 2: phase 1s: 1 of them works with torx T30 the other (the one on my car) does not...
1-20 of 74 Results
Top