Search Results for ‘rings’

A long shot, but maybe worth a try; I have bought a brand new set of original pistons for an Alfa Romeo 33 16V engine, but I failed to notice that the matching piston rings were not included. The pistons are first oversize – 87.2 mm. The Challenge is that I cannot find any source to buy...

Hello everyone! My 2.0 euro 3 TS burns an unacceptable amount of oil, so i am planning on changeing out the piston rings. I read on another thread, that some prefer 3 piece oil rings. I would be very interested in hearing from someone who have already done this, what rings did you use, where...

A bit of a long shot, but does anyone have (preferably genuine) piston rings for the 3.2 which aren't priced as if they're made of gold? Right now I have a set of NPR rings but the guy doing the rebuild isn't really impressed with the quality.

Hi all, Just wondering what key rings everyone is using. My two are here: Sent from my iPhone using Tapatalk

Hi all anyone knowif these 164 3.0 rings wouldfit a 3.0 166 Complete Piston Ring Set - 93,00 mm ( 1.5 x 1.5 x 3.5 ) Thx

Hi guys is there any after market piston rings and con rod bearings for the the 2.2 petrol 159 engine i have got the 2.2 vectra rings and bearings but the top piston ring is not as wide as the oem ones thanks guys

Hello everybody I have a Alfa gt JTS Yestaday i disassembled engine and found THIS (1-2 PHOTO) On pistons no oil drains to drain the oil inside. There is only a side drains 3 PHOTO Then ordered scraper rings inlaid type (NE EUROPE) 4 Photo Question. Do I Drilling holes on whether the piston...

I am not brave enough to open the headlights up to insert halo rings so i need to work around this issue I bought some halo rings 2x 100mm and 1x 110mm for each side and also bought the outer ring covers then silicone them inside to make sure they are extra waterproof then glue to front of...

I've been looking into lights recently for the 159. I've replaced the dipped with Hids, and the sidelights with LEDs. But I have always liked the show-look of the angel eyes. I was wondering however after seeing videos and listings, whether these where 'switchable' decorations or actually full...

Dear AlfaOwners, I repair my V6 3.2 engine Now i find piston rings and i have 2 pn of GM but I'm not sure that they fit Can you hepl me please? PN is 12631194 and 92068446 best regards, friends :read:

Hi! I’m currently rebuilding my 147 1,6 TS (120hp) engine, and i have a doubt with the piston rings, when i look in catalogs they give me two piston rings options: 71717375 and 71737072, and i don’t know which one to get. Even Fiat ePER shows both options and doesn't specify which one to use...

Does anyone know the dimensions for the condenser 'o' rings on a 156 2.5 :smoker:

Anybody heard of Cooper Rings before? You send in the block to have a recess cut out of the piston sleeve and a ring of some sort will be fitted in order for you to eliminate the use of a head gasket. Does anybody have any knowledge on this or any experience with either using or fitting this...

hi guys I stripped the head off after a pressure test as I found no compression on cylinder 2, upon stripping the head and ancilliaries after 3 hours of swearing I found.....bugger all no open valves. talk about an anti-climax! well the pistons had water in from where the waterjacket had leaked...

Greetings fellow alfa owners :) My headlights were worn out, did alittle research for the best replacement. I finally found a set of projector headlights with angel eyes retrofitted in a black gta housing. Test setup: My god those baddies changed the car ! The rings will be connected to...

Hi Does any one know if the 3 chrome instrument rings for the oil, water & fuel gauges as fitted to the s2 spider are made from plastic or metal? I know the repro ones are plastic, but I wanted to have mine rechromed if they were metal? Thanks

I recently re built 1600gt junior,on startup and running excessive white smoke,compression testing on all cylinders on spec,the liners and piston not new,but the ring set is, can the liners be glazed thus not allowing the oil rings to seat well

Can anyone point me towards a supplier for Aircon 'O' rings (HNBR) for a V6. The kits you find on Ebay do not appear to have the correct sizes and a full kit from Alfa is listed on Eper at over £50 which seems a bit excessive for a few 'O' rings.

hello just wondering does anyone know if cf3 1.6 pistion rings where used in any fiats as im finding it hard to get them,

What do you think about them. Anybody used/using them? I'm rebuilding my engine and think about trying total seal as i read good things (especially from old gtv6 owners)