Hello everyone
I've been putting up with an issue with my 156 for quite some time now and it's got to a point where I want this bugbear gone. My 156 tends to hunt during the warm up phase (not during start or normal operation) which I believe is caused by a break in the air temperature sensor...
Hello all,
I am in need of a pinout diagram for the 156 BOSE amp. I already have the wiring diagram from elearn however, my connector was cut off by the previous owner. I will need to connect the coloured wires to the corresponding pin on the amp. Can anyone help me out?
Hello Alfisti :wavey:
I am looking for the ecu pinout of my MiTo 135 multiair TCT.
Does anyone have access to e-learn in order to provide pinouts please
BR
Achilles
Guys,
Does anyone know the pin connection details for the coil pack? There are are 3 pins, I know one is ecu ground, one is 12V (active on ignition) and one is signal. But which is which?
Thanks
Zamani
searched the whole internet imo but cant find it.
does someone have a pinout schedule for the magneti marelli radionav wich comes in the 2010 Giulietta so i can try wire a aux lead.
maybe someone did the search before me and had more luck finding it.
Does anyone have this? I found this one: ausalfa.com ? View topic - BLAUPUNKT CDC A 08 CD changer cable pinout
My head unit is standard with satnav: http://img.mysoocuu.com/photo/ycarlink/uploaded/month_1203/201203101402066302.jpg
I connected to "Dauer" which seems to be permanent power even...
anyone know the pinouts to the shifter ? or have a wiring of the actual shifter resistor values etc.
its colours are 1 black and 4 white... no connector.
:thinking:
Hello, I'm trying to manually connect my Cruise Control stalk to the ECU because I don't have the pre-wire in my harness and I would like to find out where in the ECU to connect the wires from the stalk. My ECU is a BOSCH 0 281 012 882 51806557 9374D34A3AEM EDC16C39 from a Alfa Romeo 147...
Anyone know what the pinout used by the accelerator pedal of the 147 gta?
The reference is 0280752228 and, in the Audi A3 1.8T, a similar pedal has the next pinout:
PIN 1 = 5 volt reference from ECM for G185
PIN 2 = 5 volt reference from ECM for G79
PIN 3 = Sensor GROUND circuit for G79
PIN 4...
Hi, I am looking for some picture of lower (power) ISO connector. Most of diagrams I have found doesn't contain colors of the wires.
Somebody played a game with an ISO connector before me (previus owner) and mounted some aftermarket radio. Unfortunatelly some pins in ISO connector seems to be...
I have a nice Alfa 147 instrument cluster, which comes with an 18pin connector.
According to the wiring diagram on AutoData.com the pins are as below, and unlike the simpler models the 147 uses a serial differential VAN-H/VAN-L pair of wires to send all data.
The problem I now have is the VAN...
This may be of interest to a few!
I have been marinising a 2.4jtd for my boat !! Yes an Alfa in a boat!
Its not as uncommon as you think, there is a company called FNM Marine who base their engines on JTD's 1.9 & 2.4.
::..FNM-MARINE....::::: Marine Diesel Engine...
This may be of interest to a few!
I have been marinising a 2.4jtd for my boat !! Yes an Alfa in a boat!
Its not as uncommon as you think, there is a company called FNM Marine who base their engines on JTD's 1.9 & 2.4.
::..FNM-MARINE....::::: Marine Diesel Engine...
Hi to you all...I have Alfa 156 2.0 JTS Selespeed 2004 and I need to know which pins are used in my door connector and which are free..
I'm trying to put some led lights in doors to shine when the interior lights are on...so for this DIY I need to know which pin goes to keylock system and if I...
Can anyone tell me from this photo which wire is which? (Alfa 147 1.6TS Facelift)
One is earth, one is ignition switch live, and the other is live when the car lights are on.
I haven't got a tester to hand:(
DJ OD
Hi all ,
I've spent time time browsing the interweb for a good diagram / pinout for the bosch EDC16C8 ecu, as used for the 16v/20v JTD engines.
Eventually found this diagram and pinout. Might be of use to someone, certainly is to me.
My project is a throttle position activated tuning box...