Alfa Romeo Forum banner

Discussions Showcase Albums Media Media Comments Tags Marketplace

1-20 of 81 Results
  1. Alfa GTA
    Hey, a bit confused regarding what bolts I need to use with the 17" teledials, I know that I need M12 x 1.25, My old set of bolts are 25mm long for the locks and 23mm for the normal bolts Will the McGuard 27216SU fit ? (22mm long) and what length do i need for the normal bolts, is 26mm also...
  2. Alfa GTV & 916 Spider
    Hi Folks, So my 1999 Phase 2 Spider is at the garage having a few bit done (exhaust, filters.. nothing major). The guys there have said that the bolts in the wheels are too short for the wheels to be safely attached to the hubs. Torquing them up to the recommended amount is pulling the threads...
  3. Alfa 147, 156 & GT
    Hi All, I have an ’01 156 V6 that I love, even more so now I’ve fitted a Wizard catback to it (massive Kudos to Dan and all at Wizard exhausts – the workmanship is top drawer). I’ve been toying with the idea of equal length downpipes, purely to make the engine note closer to the higher pitch...
  4. Alfa 147, 156 & GT
    Hello friends, there are a lot of info about brakes, but its impossible find how much brake pipe, only 3\16, total length need for all brake line replace. From abs unit to brake hoses, marked on photo. One 25 ft roll is enough for original routes? Thank you for your attention.
  5. Alfa 147, 156 & GT
    Hello out where, at the moment my 156 SW 3.0 Swap is apart because the clutch is gone. Cause it's a CF3 car I want to delete the Manifolds. I got a Set CF2 Manifolds on the shelf. But Im unsure about the Downpipes, normally I want the real V6 sound with the EL downpipes but the car is on...
  6. Alfa 147, 156 & GT
    Hi, Anyone out there know the length of the N/S (passenger side) drive shafts including all cv joints and splines on the diesel variants? 156 1.9 16v 156 2.4 10v 156 2.4 20v I have tried checking the stated lengths on new, but some don't give the information or measure from different places. ie...
  7. Alfa GTV & 916 Spider
    Just got a super set of 17' teledials, but the bolts I have on the old wheels are to short, any ideas on the correct length i need........
  8. Alfa GTA
    I know that is a guy that made it.. Can anybody help me?
  9. Alfa 147, 156 & GT
    I have two cambelts to swap in the next few days however am struggling to find which belt to get. I have a 147 JTDm 120bhp sport, 08 reg, and a 156 140bhp JTD16v on a 55 reg. There are 190, 198 and 199 teeth lengths and obviously want to get the right one! Anyone got any pointers?
  10. Alfa GTV & 916 Spider
    Hey guys, I have fitted 20mm spacers on the rears of my spider with the blackline alloys I have just bought. I used longer wheel bolts but when putting through the alloy and spacer only 8mm of thread showed. So is 8mm of thread enough? I think I would like to buy some new longer wheel bolts...
  11. Alfa 147, 156 & GT
    Hi all I have recently acquired an 06 GT and am still exploring issues. Does anyone know (or can measure for me) the length of the lift up section of the boot. (The part covering the spare wheel that is). Mine is 88cm front to back an so somewhat short for a correct fitting and I have a gap. I...
  12. Alfa GTV & 916 Spider
    Hey was lucky enough to find a set of 17s on a dutch website and was wondering does anybody know the right size and length wheel bolts for the Zender Siena? ET 28 or 30 17s not gonna use any spacers
  13. Alfa GTV & 916 Spider
    was wondering if anybody knew what size inner tie rod i will be needing? i see some are Length: 283mm Thread measurement 1: M14x1.5 Thread measurement 2: M12x1.5 then some are Length: 290mm Thread measurement 1: M14x1.5 Thread measurement 2: M14x1.5 and some are 303mm and 307,7mm so...
  14. Alfa GTA
    Guys have a supersprint cat back on the car was already fitted when I bought the car am thinking of putting decat manifolds on and equal downpipes any idea on how it would sound Anyone have this already setup Ta
  15. Alfa GTV & 916 Spider
    Afternoon peeps, I have recently acquired a (1995) 916S2 spider 2.0 ltr that has another dipstick in the boot. The previous owner mentioned a dipstick issue and I'm now wondering which is the correct one. I did an oil and filter change refilling with carefully measured 4.4 ltrs whch came above...
  16. Alfa GTV & 916 Spider
    HNY folks! I was looking at a cheaper alternative for the very pricey Alfatune equal length downpipes for the V6 and found these Peco ones from Larkspeed: Peco Stainless Steel Equal Length Downpipes (Pair) for Alfa Romeo - larkspeed.com Has anyone bought or tried these? If so what was the...
  17. Alfa 147, 156 & GT
    HI! I have a quick, but maybe difficult question. (as the Q4 is rare round here) Does anyone know if the driveshafts for the 156 Q4 are longer than standard, and if they will fit a 156 GTA diff and gearbox ?
  18. Alfa 147, 156 & GT
    Anyone Know what length the serpentine belt shold be on a alfa 156 V6 24v if no AC kompressorn is present.
  19. Alfa GTA
    Hi What's the standard wheel bolt length ? i want to replace mine because they have gone rather rusty. I think the thread size is M12x1.25 but unsure of the length.
  20. Alfa GTV & 916 Spider
    I have had my longlife quads on the car for almost 10 years now, very happy etc. its a cat back system and does sound pretty special. However, I am aware the flexi's and cat may be dying soon and the downpipes are probably original (or at least 15 years old as I have not changed them!) and I...
1-20 of 81 Results
Top