Alfa Romeo Forum banner

job

  1. Paint job cost

    Alfa 147, 156 & GT
    Quick question: how much do you estimate it would cost to get the bonnet and the 2 mirrors resprayed?
  2. Ebay 156, values, another good job at Auto Alfa!

    Alfa 147, 156 & GT
    A couple of months ago or so I bought a 156 1.8 Lusso from Robert in central London (some of you may know him) following some interesting bidding on Ebay. The advert stated that the belt service was carried out by Alfa Lusso in Sussex last year but they have never returned my calls or...
  3. Local garage wont replace my bonnet cable...to big of a job?

    Alfa Giulietta
    Hi guys, so a local garage to me who last year did some major work on my wifes old x5 dropping the whole rear sub frame and replacing brushes and brake pipes today have refused to replace the bonnet cable on my alfa guilietta. A couple of weeks ago I booked my g in after phoning for a quote and...
  4. Alfetta GTV6 rear bearing job

    The Classic Alfa Romeos
    Hi all, I'm currently refurbishing the whole rear suspension. dedion and transaxle are out of the car. At this point I would like to replace the rear bearings too but don't have and can't find the proper tools to do the job. This job: Replacing Alfetta Rear Wheel Bearing ? Dep-O Magazine The...
  5. Replacing fog lights on 159 TBI TI - easy job?

    Alfa 159, Brera & 946 Spider
    Noticed one has the front glass broken and the other is badly tarnished, so was thinking of replacing. Is it a relatively easy job or should I leave it to the garage (they will be having the car soon anyway for some other work)? Thanks
  6. Alfasud bits job lot - Nr Banbury UK

    Alfa 33, Sud & Sprint
    A mate had a ‘sud racing car. These were left over when he sold it. £100 the lot. 4x Koni shocks - used 2x strut bodies with suspension arm attached 3 x front calipers 3 x gear linkage metalwork 4 x front hubs with driveshafts 1 x front hub no shaft 1 x starter 1 x alternator not working...
  7. You only had one job....

    Alfa Stelvio
    Just received an email from Alfa Romeo UK inviting me to test drive the new Alfa Romeo "Stevlio". On one level it's only a typo and we can all make mistakes. On the other hand.....
  8. Today's job....

    Alfa 159, Brera & 946 Spider
    Can you guess what I've been doing?
  9. Replace rear anti-roll bar drop-link, DIY job?

    Alfa 159, Brera & 946 Spider
    Is replacing the rear anti-roll bar drop links an DIY jobb on the 159? How is it done?
  10. 156 1.9 jtd driveshaft job, the same both sides?

    Alfa 147, 156 & GT
    156 1.9 jtd driveshaft job, the same both sides? (Opdated it depends) Hi, I was wondering if changing the driveshafts is the same job on both sides. I have done the gearbox side, but I am unsure if the opposite side involves more parts. If so, is there a writeup or guide anywhere? EDIT...
  11. Mito tailgate wiring loom - DIY job?

    Alfa MiTo
    Hi all I've got the tailgate wiring issue with the rear wiper going mental. Is this something I can fix myself? I think I know what part to get but I've no idea if it's easy to fit. If someone who's already done this could give me some idea I'd be extremely grateful.
  12. Stopped - Print job was not accepted

    The Technology Section
    My new Brother HL3140CW has been just fine. Then the other day I printed something, but it didn't emerge. I checked the queue and it said pending. I opened the job and it said Stopped - Print job was not accepted. Any ideas? :coat:
  13. Change front drop links, DIY job?

    Alfa 159, Brera & 946 Spider
    I am hunting Down some knocking from the front suspension. Changed the upper wishbones helped some. But there is still some knocking. Thinking about changing the drop links since they are pritey cheep compared to other front suspesion parts. Is this a simple, bolt off - bolt on type of jobb?
  14. GTV 3.0 916 Clutch Master Cylinder Job Photos

    Alfa GTV & 916 Spider
    For the record: photo from engine side of the bulkhead and footwell side once the new pipe work and cylinder were installed. I pulled the pipe from the engine side once the cylinder was connected with a jubilee clip to pull the cylinder into position. The idea that you can replace the cylinder...
  15. Got my dream job - still learning tho . . .

    General Motoring Discussion
    .
  16. This week’s bit of a job and some free bits!

    Alfa GTV & 916 Spider
    Everything in the picture was removed over the last couple of days and will be renewed with all new parts, mostly! http://www.alfaowner.com/Forum/attachment.php?attachmentid=638602&thumb=1 The day before I started every nut and bolt was dowsed in releasing oil. It took about two hours just get...
  17. This weeks little job

    Alfa GTV & 916 Spider
    All this came off over the last couple days http://www.alfaowner.com/Forum/attachment.php?attachmentid=637834&thumb=1
  18. ts a hard job to replace a 3.2 Q4 Brera!

    Alfa 159, Brera & 946 Spider
    Well I am not a frequent poster on this forum, more of a browser of other peoples posts, however this month its 3 years since i bought my Brera 3.2 Q4, its now nearly ten years old, only has 52k miles on it and I wanted to post a positive posting to show there are some good cars out there ...
  19. Aux belt - Easy job?

    Alfa 147, 156 & GT
    Got my 72k service looming... No records of the Aux belt ever being done in the cars history, so it's due! I'm happy doing the oil and filters on the driveway, and have done brakes, downpipe/precat replacement, slave cylinder replacement at home too... Been reading a few guides, and it seems a...
  20. Wouldn't wish this job on anyone.............

    The Classic Alfa Romeos
    Being A Test Driver For Alfa Romeo Is The World?s Best Job | Petrolicious
Top