Search Results for ‘gaskets’

Found some gaskets in amongst a relative's garage clearance. Anybody able to identify this one please?

I've taken off my rattling cat section of the exhaust and am going to put my Wizard decat pipe in place of them. When the cats were removed the gaskets are all crumbly at the front end and non existent at the rear end. I've searched for replacement gaskets but can't find them in the normal...

Used upright door gaskets right and left for Alfa Romeo Gtv 916 Still in usable state and come off my car £70 plus postage Sent from my iPhone using Tapatalk

Noticed a small weep from the sump area of my GTA and have checked eper to get the part number of a sump gasket but appears GTA's dont have one? They show a pot of sealant instead! Is this right?

Hi all, I have had to replace pistons ,head and big ends following the inlet cam jumping teeth on my engine.(32310) I have acquired a head gasket from eurocarparts | Car PartsRetailer and it doesnt have metal cylinder liner rings like the one that came off. Im a bit worried that if I use...

Going to be doing my timing belt in the next few weeks, Thinking it might be a good plan to do the head gaskets while I am at it. Car seems to run ok but I am losing a small amount of water weekly say 10mm down in the header tank over 150 miles or so. Basically what I am asking is if the head...

Hi Everyone. I run a '94 164 super with the 12v engine. The engine was recently replaced with something slightly earlier and bodged (expensively!) but was running ok for a little while. Now one or both cylinder head gaskets has gone due to an epic overheat due to a fouled radiator (I think -...

Hi all, i have the black smoke control module engine failure problem on my 2004 GT. i stripped the EGR valve off and cleaned it up, and it looks like someone has been in there before as the gaskets are missing, what effect will this have on the car? and does anyone know the part numbers for...

yes i know that ol' chestnut... Been to see Enzo at Autocasa today and he's informed me that the boost leak i thought i had, is actually an exhaust leak from the EGR. he's suspecting the 'flat' gaskets that sit between the convoluted pipes and the cooler as crap-ly circled in this image. as...

Hi wonder if an one can point me in the right direction for the 2 manifold to join exhaust down pipe gaskets on the 3.0 V6 in my case a 91 SZ. I can find people selling what they term ARG2 = AR 11601017200 gaskets which suit the 2.0 engine with a 45mm diameter hole and 65mm distance between...

Hi All, Proud new owner of a gleaming black 156 with red interior. Need to do some mechanical jobs, so am downloading the E-Learn file. Top of the list of jobs is head gasket replacement. I will be overhauling the head, replacing valve stem seals, renewing timing belt, water pump & associated...

Had a fault code p0237 come up and it looks as if the actuator arm isn't moving very much at all so I have decided to clean the turbo with innotec spray and try and get the vanes moving again as I had some lying from when I was going to do my old BMW.does anyone know what gaskets I will need to...

I need to replace these gaskets but when I popped in to the Alfa dealer the chap said they don't show up on the system and that often the factory would install parts that were not offered aftermarket and that I should just use some exhaust paste. I can't seem to find them with the usual suspects...

I need some new gaskets for when I take off and polish my intake pipes this weekend, can anyone let me know the best place to source them from? Cheers

Just a quick question is it possible to replace the two sump gaskets without removing the engine and if so are there any other bits of gasket/seals that can be accessed and replaced at the same time Many thanks john

Hi all, Cutting a long story short: I've got a GTV 3.0 V6 with a nice blown head gasket :) It's not massively bad at the moment, in fact, Phil from Alfacraft said I should give Wondarweld a try, says he's seen it work miracles in the past. Otherwise it's a pretty big job and fairly costly as...

I want to check my plugs, but to do so, you have to remove the inlet manifold. Anybody know if you can use the Holden/GM inlet manifold gaskets in lieu of the Alfa ones? Alfa are £40 each, Holden are £20 a pair!

Hi guys are the rectangle and the diamond gaskets reusable after a clean of the EGR? thanks

So I'm finally getting around to replacing all the coil packs, having exhausted all other options trying to resolve this problem. To get to them I'll need to remove the intake manifolds and therefore replace the gaskets. The trouble is no one seems to have them.. Euro's have them on...

Is there anywhere to buy these cheap and not in gaskets sets please