Alfa Romeo Forum banner

fittings

  1. Clips, brackets and fittings

    Alfa 147, 156 & GT
    Hi - I would like to replace some old, broken clips in/around the scuttle panel covers and the underside of the bonnet on my GT. In order to find out factory locations, how many of a given part there were when new, prices & availability, would I need ePer? If so, is this something I need to...
  2. Spider S4 Header Rail Fittings

    The Classic Alfa Romeos
    So I'm replacing the Header Rail along with the soft top. Sadly the original fittings to the frame cannot be reused. Has anyone been able to source these - they are unavailable at the regular suppliers such as ClassicAlfa. Thanks in advance for any help.
  3. 105 Brake line fittings

    The Classic Alfa Romeos
    Anybody know what fittings the brake flexihoses are on the 105 ?. I seem to be having trouble getting a new set of Goodrich hoses to fit with female fitting on the line leading from the Tee piece. Seems to be OK at the caliper end. It is quite possible somebody has buggered about with them at...
  4. 2009 159 lower suspension arm fittings

    Alfa 159, Brera & 946 Spider
    Hi all, I have seen some of the threads on the lower suspension arm ball joints creaking and I have replaced some over time and also managed to lubricate some. The car (2009, Special Edition 1.9 JTDM) has just failed its MoT due to the ball joint now having excessive play (!) so I am having to...
  5. 159 brake hose fittings to 156 ?

    Tuning & Upgrades
    Hi all i have a small question. Are the m10 female fitting on a 159 front brake hose the same fitting as on a 2.5 156 Thanks
  6. 1991 164 Rear Brake Proportioning valve fittings needed or??????

    Alfa 164 & 166
    Greetings- I am in the process of replacing the two steel brake lines (rusted/leaking) that run from the front of the car , over the gas tank, and then into the proportioning valve at the rear of the gas tank. The problem that I've encountered is that these brake line fittings are machined...
  7. Brera Front Undertray fittings

    Alfa 159, Brera & 946 Spider
    Does anyone know where i can get all the fittings that secure the front undertray it looks like a fair few are missing at the front which attached to the bumper but also underneath the engine too, I've noticed a lot of mine are missing and also the undertray is unsecure on one side at the back...
  8. oil cooler fittings

    Alfa 147, 156 & GT
    I've read plenty of threads about the problems with the GT's oil cooler pipe fittings corroding but nowhere can I find what thread form the fittings use at either end, and the engine end in particular. Does anyone know?
  9. Fittings for Prodrive mudflaps

    Alfa 159, Brera & 946 Spider
    Just picked up a set of plastic clips for the Prodrive mudflaps from my local Subaru dealer at the grand price of £2.52 for 5 (smallest quantity they will supply) including VAT. Part number is 759114020 & they arrived within 3 days of being ordered. These are the genuine ones which were...
  10. HELP; GT Bumper Grill Fittings

    Alfa 147, 156 & GT
    Hi All, In brief, someone whom shouldn't have a driving licence reversed into my car:rant:! At first glance there didn't appear to be any damage, but then the grill under the bumper was out of place and just came off with the slightest tug. The grill doesn't appear to be broken and I've had a...
  11. 159 Mats - Specific Fittings

    Alfa 159, Brera & 946 Spider
    Hi All. I'm looking to get a set of mats for my Ti. I notice that connectors something like these are fixed to the floor in each area i.e. drivers, passengers and back seats. Has anyone got any recommendations for ideally generic mats. Even the official mats seem to only have connectors on the...
  12. Alloy fittings

    Alfa 147, 156 & GT
    I know you're probably sick of these questions on here, but I'm not too clued up on offset's and PCD's of the Alfa alloys yet. Will these, apparently from a 156, go straight onto a 147? I'm sure I remember seeing somewhere that they won't fit, but I thought I double check first. Any help...
  13. Oil cooler fittings

    Alfa GTA
    Am I right in thinking they are 5/8" bsp? wrinx
  14. Wind Deflector Fittings - HELP !!

    Alfa GTV & 916 Spider
    Hi all, I purchased a wind deflector from Ebay last year - all fitted and no problems. The fittings are not the standard metal bars attached inside the cabin but instead a hole needed to be drilled and the following hollow bolt inserted into the cabin. Then a spring released bolt from the...
  15. Rear number plate light fittings ?

    Alfa 147, 156 & GT
    Hi All, I recently had to prise out the two rear number plate light fittings, but I don't seem to be able to refit them. It may be that I've broken something or bent something in the process. The inside of the housing is flat and doesn't have anything to connect to. Here's what I have. Does...
  16. Boot interior fittings/fateners

    Alfa GTV & 916 Spider
    Hi, over the years some of the boot interior fittings/fasteners in my GTV seem to have gone missing. These fasteners are the grey plug type and the white screw type. Where would I go to source some replacements? I imagine others have had these gone missing as well :) @veloce
  17. Roll hoop fittings, or lack of them!!

    Alfa GTV & 916 Spider
    Folks I'm sorry to be a pain but here's the dilemma.... I've been rather extravagant and purchased new roll bars for the Spider off E-bay to the tune of £330 (a fool and his money you may well think!) The company masquerades as Cabriotrade based in Surrey.....Apart from waiting for over two...
  18. Wanted - Ts airbox and full fittings

    Alfa 75, RZ, SZ
    Anyone breaking a Ts and don't want the full airbox/snorkel/brackets etc? I'm after a standard setup
  19. Brake Pipe size and fittings

    Alfa 147, 156 & GT
    during the engine replacement of my latest project the usual drivers side brake pipe needs replacing was wonderin if anyone knows the diameter of the pipe required and the end fittings...
  20. 159 Boot trim fittings

    Alfa 159, Brera & 946 Spider
    I've managed to snap 3 of these when removing the boot lid trim to fit the cargo net. Anyone know the part number / price (I'd prob order 6 or so to allow for future ****-ups! The plastic is very brittle. TIA!
Top