Alfa Romeo Forum banner

crank

  1. Crank Sensor Failure Question

    Alfa GTV & 916 Spider
    Please could somebody perhaps wiser than I on this advise. From a previous thread on the subject, opinion seemed to be that I should replace the crank sensor on the P2 TS GTV I am recommissioning. Well I've got the exhaust off and the sensor bolt out but its stuck in the engine and I can't get...
  2. 147 2. TS Crank Pulley Removal

    Engines (TS, JTS, JTD & V6)
    Hi. Could some please tell me how to remove the crank pulley on my 147 2.0 TS engine. Do I need a articular type of pulley? Alos what type of spanner is required to undo the aux. belt idler? Thanks
  3. GT Crank sensor replacement

    Alfa 147, 156 & GT
    HI guys, I have a 2006 1.9jtd, and after lots of searching is seems my crank sensor is the culprit. I have the following symptoms: car cuts out when it it gets hot, after a 30 km trip or so, if you wait a while for it to cool down , it will start up again, but it runs rough. Seeing that it may...
  4. Crank sensor 916

    Alfa GTV & 916 Spider
    Trying to remove old sensor and can't find the Allen key bolt to remove the sensor which is supposed to be above the starter (can't even find starter) Is starter on right as you look in bonnet and are you supposed to remove sensor from top or bottom. Seen pic online but not very clear can't tell...
  5. P0335 crank sensor

    Alfa 147, 156 & GT
    Hello all, new to the forum- so be gentle please?!! I have a 2004 alfa 156 1.9 jtd. Recently broke down at home. My local garage diagnosed crank sensor and fitted a new (genuine) one. Still wont start, except using easy start. Cleared codes, same code re-appeared -P0335. When engine is cold...
  6. V6 damage. Crank pulley

    Alfa GTV & 916 Spider
    Upon dismantling my 3.0 I noticed damage on the rear of the crank pulley and on the engine itself. Sorry haven't mastered the art of posting photos yet. As the bottom end had gone, allbeit a big end, I thought this may have been caused by excessive end float but none is obvious and it is...
  7. Looking for crank timing pulley

    Alfa 147, 156 & GT
    Anyone know where I can get a new crankshaft timing belt pulley for the 2.0 ts engine year 1998 ? Preferable in Europe and that ships within Europe. My woodruff key is gone, I noticed it in time before it slipped totally, so no damage to the engine, just the timing was off a bit. Alfaworkshop...
  8. Lightened crank pulley

    Alfa GTV & 916 Spider
    Has anyone fitted a light weight undersized crank pulley. Looking into sourcing one at the mo. I know AutoLusso do a kit for £175. Would like to know the benefits of someone actually running one thanks.
  9. 156 v6 crank sensor

    Alfa 147, 156 & GT
    Does anyone know if I can use a 2.0 twinspark crank sensor in my v6 as I have one and need to check if the sensor is the fault in my v6 ? Anyone ever tried?
  10. Alfetta 2.0 GT front crank pulley - easy removal

    The Classic Alfa Romeos
    Well I have been struggling to get my front pulley off. 3ft breaker bar and 6ft scaffold pole wouldn't budge it. I don't think the full problem is how tight this nut is more to do with the rubber donuts in the propshaft not locking things solid. Well today I bought one of the following for...
  11. Crank bolt

    Alfa 147, 156 & GT
    Just want to confirm the crank bolt is a LH thread (ie turn it clockwise to undo) I have been trying to get mine out for a week now, i have used the largest rattle gun i could find ( maybe 800-900nm) and i have tried putting a bar on and hitting start (it doesn't move). Is there something...
  12. CF1 3.0 Crank Sensor

    Alfa GTV & 916 Spider
    Hi all, can anybody post a link or advise me on purchasing a CF1 3.0 crank sensor for a phase 1 3.0 GTV? Thanks, Phil
  13. replace crank sensor 2.4 10v

    Alfa 147, 156 & GT
    Can anyone help me by giving me the steps to replace the Crank Sensor on my 2001 156 2.4 JTD 10v.
  14. Crank bearings

    Alfa 33, Sud & Sprint
    Hi all , Any recomendations reagrding what crank bearings to get for a fresh 16v engine ? I have skimmed the crank .010 I was told to get LC (Lead Copper), heavy duty ones. Where should I look ? Any part number on the top of your head :devious: ? Thanks
  15. '82 Alfetta GTV - Water Pump Change - Remove Crank Pulley?

    The Classic Alfa Romeos
    So the job this weekend is to change the worn out pump. It is the late type with pressed on pulley and timing mark. I have read up on this and it seems that there are two options:- 1) Remove the crank pulley. 2) By locking two nuts onto the bottom studs of the water pump remove the two bottom...
  16. Crank Sensor

    Alfa 147, 156 & GT
    Hi all, a bit of advice if possible, I have a 156 1.9JTD the revs won't go over 2750 in any gear so big loss of speed and acceleration, after searching through forums the best solution I can see is changing the crank sensor I'll do that but is there anything else that has to be done to it after...
  17. 3.0 with 2.5 crank question

    Engines (TS, JTS, JTD & V6)
    Ive read as much as i can about the 2.8 conversion, But there seems to be some confusion on the way to go. version 1. I want to know if i can put the 2.5 crank in the 3.0 engine using the 3.0 heads etc. version 2. or do i have to use the 2.5 block and machine it for the 3.0 liners and pistons...
  18. 156 JTD 10v - Crank Pulley

    Alfa 147, 156 & GT
    Whilst investigating what sounds like a dry aux belt pulley bearing I noticed the crank pulley rubber looks very perished. Should I be replacing this too?
  19. Crank Pulley Help Please.

    Alfa 155
    Morning Gents, I hope you are all well? If you look at my previous thread, you will see that I eventually found a new tappet cover. Fit the new one and started her up. But......(always a but :depressed:) There is absolutely no oil reaching the valves and the cam-shafts. I check the oil...
  20. Crank Pulley & Nut needed for V6?

    Alfa 155
    hi all my current 155 project is in need of a Crank Pulley & Lock nut to reinstate the engine, does anyone have anything available or know of anyone breaking a V6? thanks in advance SB
Top