Search Results for ‘block’

My engine builder has asked that I clean the block internally but I have some difficulty as the crankshaft has been left in situ (He says that the front pulley nut is very difficult to remove) and I am terrified that debris may go undetected. Is it safe to try and clean the block with the crank...

My engine builder has asked that I clean the block internally but I have some difficulty as the crankshaft has been left in situ (He says that the front pulley nut is very difficult to remove) and I am terrified that debris may go undetected. Is it safe to try and clean the block with the crank...

I'm still doing my 3.0 v6 build (not much spare time to do it in) so bought a complete 12v 2.5 v6 (engine number matches the gtv6 type) to take the ancillaries off. Once I'd dropped the heads I discovered it was as rusty / gunky as you'd expect a GTV engine which has been standing for years to...

Could anyone tell me if the 2.0 TS block is exactly the same or interchangeable with 2.0 L Fiat Coupe or Lancia Delta Integrale 2.0 16V?

Could anyone tell me whether a CF2 16v head will fit on CF1 8v block?

Could anyone tell me whether a CF2 16v head will fit on CF1 8v block?

Could anyone tell me whether a CF2 16v head will fit on CF1 8v block?

I need to order new bearings for my 2.0 TS but the engine numbers are missing. The donor car was also scrapped years ago and I don't know if I have any records of its registration plate. Is there a solution?

Hi All, As I am new to this forum, please be gentle :blabla::blabla: I am guessing this topic was already discussed but I haven't found it, so i am opening a new post. I have a 1.5 dual carb, 1992 33 and I'm thinking about putting a 1.7 crank in it to make it a 1.6 and have a few questions...

Hi all,on my '07 Alfa 147 I am experiencing an unusual situation regarding the turning signal block: if the steering wheel is just slightly turned to one direction,I cannot make the turning signal to stick to the opposite direction. Let's say steering wheel is slightly to the left,as in going...

Used forum guide - the photos were a great help. I've taken the bumper off 2008 159 because of the 'Parking help not available' issue. The non 'clicking' sensor by the the number plate needed replacing. Bought one and painted it Titanium grey :rotate:- all good. Problem came when replacing the...

Hello guys, to be frank I am not an AR 164 or 166 owner and I never was. I own Spider 3.0 V6 12V 1999 that got scratches on the crankshaft (oil leaked thru the oil cooler and... :dead:). I was wondering if anyone know where I could look for a block or crankshaft from 164 produced after 1992...

Hi folks, is it possible to fit 1700 heads from 145 boxer 1.6 on 1400 80 mm block? thanks

hi guys , can anyone help me with a issue l have with my 166 , l replaced all head studs in block , tensioning all nuts to head , now having troubles with one stud , it wont hold tension at spec, its pulling stud up slowly when tensioning , is there a way i can lock the stud in the block without...

Hi All I;m from down under, thats right Australia, "Land of plenty" of outback and corrugated roads, Kangaroos and Emus. So it may seem odd that Alfas have any chance of surviving in this hospitable place. Well we also have plenty of bitumen in between. Like our road from Perth on the west coast...

Am i the only one ever that has got one of the unions? (edited, ty Taylor) wrongly inserted & didnt recognize before it was halfway down :-( Is it new block or chances for a garage can redo threads? Good advice..Dont try it in the driveway while its thunder & rain, lamp almost out of battery...

My car has been listed as status 20, that is to say, built, since Jan 20th but has failed to make further progress. Two days ago I received the following email from my dealer :- "I have spoken with vehicle supply this morning who have confirmed that your Quadrifoglio and another Quadrifoglio...

Hello, We are making racing engine to compete in FIA central Europe racing series. Currently we have 3.0 V6 24v engine but that isn't enough as we want to get closer to 400bhp mark. The cheapest way to make it work is to use turbo but regulation to use engine with turbo is max. displacement...

Does anyone have a decent usable 2litre 145, 146, 155 crank or block with crank that is surplus to their requirements. I need it for my 155 Super that I bought with crank that had run bearings and I want to rebuild. The problem is the motor in that car is a 156 motor (and therefore so is the...

I'm Joe and I'm in the process of buying an Alfa Romero Brera 2.2 JTS SV so hoping to get some hints and tips from this forum. Just sold my MB SLK350 V6 to fund my next project. Cheers Joe