Alfa Romeo Forum banner

bits

  1. Carbon Fibre bits

    General Motoring Discussion
    There’s discussion about getting carbon fibre bits for our cars. I had the carbon mirror caps on my Giulietta and they looked great, but no lighter than the plastic originals. The Giulia and Stelvio come with a carbon drive shaft which must be beneficial in weight and rigidity terms. The...
  2. Loads of Busso bits for sale

    The Classic Alfa Romeos
    I'm trying to raise some cash to replace my cylinder heads and clear some space for dismantling my pair of transaxles, so I'm selling off the parts left over from my 3.0 12v rebuild and experiments: GTV-6 / 75 2.5 12v stuff: 2.5 12v Busso pistons - really good condition 2.5 12v Busso flywheel...
  3. Carbon fibre bits

    Alfa Giulia
    I just bought a Stelvio Milano in Misano Blu. Love the car but I love the carbon fibre trim which is on the TI and Quadrifoglio. Has anyone upgraded their internal trim with after-market carbon fibre bits? If so, where have you purchased from and are they easy to fit? I am thinking the...
  4. Carbon Fibre bits

    Alfa Stelvio
    I just bought a Stelvio Milano in Misano Blu. Love the car but I love the carbon fibre trim which is on the TI and Quadrifoglio. Has anyone upgraded their internal trim with after-market carbon fibre bits? If so, where have you purchased from and are they easy to fit? I am thinking the...
  5. 156 GTA parts and other bits

    Alfa 147, 156 & GT
    I'm having a clear out of my excessive 156 spares and I've listed a few bits in the Upgrades section. If you have a 156 and need to improve or change or repair anything then have a look.
  6. 156 GTA stuff and other bits for sale...

    Tuning & Upgrades
    So over the years my 156 has been lovingly cared for and upgraded. I became a bit of a hoarder of useful parts which I now need homes for. I'll put everything on here for a while before ebay ... Firstly, I have everything you need to put 305mm Brembo brakes on a standard 156: GTA drive shafts...
  7. Starter motor for 12v 3.0 164? Will others bits fit?

    General Alfa Discussion
    I have bought a non running 12v 3.0 164 motor for my MX5 V6 project that needs some bits... Older 12v parts are hard to find in NZ... Questions.... will a later start and flywheel fit at all? What about later injectors?? They would be easier to find. The learning continues.... I have the...
  8. Bits and bobs

    Alfa 75, RZ, SZ
    Hi everyone, First thing is my rear cv joints have quite a lot of oil around them, any ideas on what I should do? Is there a seal on them or nit to worry? Secondly I have a nice set of four 75 alloys with nearly new Toyo tyres if anyone is interested in buying them ? Also a decent CSC rear...
  9. Rusty bits advice

    Alfa 147, 156 & GT
    Hi all Despite the jts not seeming to be suffering from any terminal rust, when i look underneath there's loads of bits that im not happy with! I have a vague plan in my head tgat at some point during the summer im goung to... 1) Get a hardy wire brush and put her up on axle stands and , whilst...
  10. Rusty bits

    Alfa 147, 156 & GT
    So, now that i have most of the mechanical stuff under controĺ (fot the moment anyway...sigh), theres a couple of bit of bodywork that need attention. Im going to add some photos and i was thinking of tackling them myself...though a bit scared at the prospect! Its basically road rash on the...
  11. Gearshift rod in bits !

    Alfa 147, 156 & GT
    I am trying to work out what's missing , so according to eper the parts I want to show inside the gearstick sleeve has no spring on my GT.Has it has come adrift and looking at the picture I picked of a thread on here, there is a black sleeve over the main shaft with a spring, but I seem to...
  12. Website link for Alfa bits

    Alfa 159, Brera & 946 Spider
    Hiya What was that website for alfas where you can drill down into vairuos bits and identify all teh parts?
  13. Bits to sell now its gone

    Alfa GTA
    Hi all I have a few bits to sell now my 147 GTA is sold and my wife wants the room in the shed. 2 sets of peddle rubbers $25AUS including postage 1 Autlusso adapter to enable fitting of Ferrari 360 T.B. to Alfa plenum chamber $45 AUS plus postage 2 carbon fibre rear view mirror covers, I...
  14. Identity of these bits! In name or num

    Alfa 147, 156 & GT
    Hi all, I've got a rusty engine bay that I want to clean up, what are the formal names or numbers for the parts on the attached pictures? Cheers all, demps
  15. Help -- need 164 bits

    Alfa 164 & 166
    My lovely 1990 164 ts did a stirling job at its first tougher MoT yesterday , passed with just 2 defects . finding the replacement parts is proving difficult tho. I need a NSF steering rack rubber gaiter. Most spare parts dealers only sell a whole rack . Ive heard maybe some peugeot gaiters...
  16. Bits needed, brake carrier and lock.

    Alfa GTV & 916 Spider
    Couple of bits needed. 1st is one of these battery compartment clips, the one behind the drivers seat (RHD) 2nd is a Bendix front brake calliper carrier, must have good threads and mounting bolts. Thanks
  17. Gaiter shredded to bits!

    Alfa 159, Brera & 946 Spider
    So what do you think is going on here? This gaiter/boot seems shredded to pieces! Any idea what could have caused this? Also, could this be the reason I've been getting creaks/thuds when steering close to full lock at low speeds...? In which case, what other parts am I going to need to order in?
  18. Trailing arm and other bits

    Alfa 159, Brera & 946 Spider
    Soooo, that fatal rust has set in. I need to remove the trailing arms, does anyone know the size of the torx bolts holding them in? I've been scouring the internet for days and can't find anything... Also looking for a skirt for the drivers side if anyone knows of one. So much work to do :rolleyes:
  19. Couple of bits to sell on

    Alfa GTV & 916 Spider
    Now that I have done my Cams and also the engine bay clean up I have a few spares from my car that came off willing to sell. Looking to recover back what I paid for interim items I refurbed. Set of Rocker covers “ note we think the ones on mine front is from a GTA as has plastic blank plate...
  20. Alfasud bits job lot - Nr Banbury UK

    Alfa 33, Sud & Sprint
    A mate had a ‘sud racing car. These were left over when he sold it. £100 the lot. 4x Koni shocks - used 2x strut bodies with suspension arm attached 3 x front calipers 3 x gear linkage metalwork 4 x front hubs with driveshafts 1 x front hub no shaft 1 x starter 1 x alternator not working...
Top