bar

Phase 3 radiator grill has one chrome bar broken. Can this bar be taken off and replaced without taking bumper off? Any ideas please?

Hi Spoken to a couple of tow bar fitters and they are reluctant to work on my Alfa Giulia Veloce. Can people recommend any garages who have done a good job on your alfa fitting a towbar? Im based in Surrey but would be willing to travel to get a proper job done. Thanks for any tips

Hi, I've owned a relatively low mileage (65,000) for a few years now and finally got around to rebuilding the front suspension to rid me of the traditional knocks & clunks for these models (& why not just put a new clutch in whilst the sub-frame is down!). So, having purchased some 22mm...

Is there anyone out there who can assist in me buying a towbar for my Brera, preferably detachable and a flange fitting. I believe they only did a swan neck. I need to carry my moto x on a bike rack. Cheers Dave Kemp

Hey guys, So lately my Alfa started to believe that it's a kangaroo and was hopping like mad and sometimes not engaging first gear. Turned out to be EV0. Changed it - all good. :silly: Though in FES, I've noticed that my max pressure is 47.9 bar and the pump engages around 37-ish. I can get...

Hi guys, my Spider went for a MOT this week and it was noticed that one of the front anti-roll bar brackets had snapped and the chassis mount has split . I had the alloys powder coated recently and new tyres fitted without tubes as had previously been in them. I thought the steering had felt...

Hi, This is for a sport wagon. On the 7 pin connector of the tow bar I’m only getting voltage from the indicators, all the other terminals are dead, so I’ve no tail lights or brake lights. I may have fused part of it when I wired up a new socket onto the bike rack- I lost the original on a...

Hi, I've removed the front sway bar on my 1982 gtv and noticed that the sway bar end links are on a slight angle , I should have taken better photos but I can't make out in the photos I've taken do they angle in or out, thanks for any help, cheers.

As some of you might know, the 156.net forum is no more. We knew that the site was going down for a while (lack of traffic) so I took the opportunity to save some of my (hopefully) useful threads. I initially posted this July 2012 and subsequently updated the thread to include a guide on...

Does anyone know correct part number for the 24 mm TI spec front Anti Roll Bar?

Hi,I have received a new Eiebach rear bar for my V6 GT and it was at my mechanics to get fitted yesterday but he rang me to say he couldn’t fit it for a couple of reasons.He is not an Alfa specialist and there isnt one to seek advice from where i live so I am seeking some help. 1.The Eibach bars...

some time this year I want to change the front anti-roll bar, my subframe looks a little worse for ware so i’m Thinking of having that swapped over with a refurbished one at the same time. What would be a ball park labour figure/budget to have these swap over?

Hi, just had my MOT done and told the mechanic it sounded like the exhaust was loose at the back somewhere as I can hear (and feel) it rapidly vibrating when driving, especially when pulling away. I expected that it needed new rubbers, however when the car was up on a lift, the mechanic invited...

On my 2.4 brera when I accelerate my turbo bar goes to 1.4 straight away but as I keep accelerating my turbo pressure drops down to 0.8 bar. Is this normal??? My foot is not lifting off the gas at all for this to happen.

Hi Guys, Hope everyone is well, just wondering if anyone has recently installed a strut brace / Bar ? I have one in mind and looking in the engine bay before there is some already pre drilled holes thats dont seem to be doing anything, just wondering if they could be used ?? Any help or info...

Has anyone replaced the rubber bushes on the front anti roll bar? I've just removed the front anti roll bar and although the Eper drawing shows each of the clamps as an upper and lower part, mine are joined together very well indeed and don't want to come apart. So the clamps with the rubber...

I have an 05 156 JTS and would like to upgrade all the bushes so can anyone please help me on correct diameters for the front and rear anti roll bars please it would be much appreciated, also has anyone out there ordered this kit from strongflex and how did you rate the quality. Many thanks...

1998 PH1 very early 3.0 24v as my front subframe is coming out for other work i decided to replace the front subframe bushes on the front because as far as i know they are probably original, did order these from Demon Tweaks...

Just about to remove the front sub frame so my garage can get to do the clutch and flywheel, This means my sub frame will be off the car, I really need to help with what should i be looking at and changing while this part is removed, Can you offer help as it may not be off again for some...

re: rear sway bar p1 96 spider 2.0ts Hello all, Does anyone know if the larger 20mm rear sway bar ( I think on v6 cars) will swap out directly with my rear 18mm sway bar. My car is a 96 spider 2.0ts. I have good luck putting (slightly) larger rear sway bars on front wheel drive cars to help...